Digi Launches XBee-PRO 900HP RF Module With a Range of Up to 45 Km

Digi International has recently announced the XBee-PRO 900HP RF embedded module based on ADF7023 transceiver and Energy Micro Cortex-M3 EFM32G230 MCU @ 28 MHz. The company claims the module supports a line-of-sight range of up to 45 km with a high-gain antenna and data rates of up to 200 Kbps.45 km is not quite enough to communicate in space (100 km), but that’s still a pretty good range. Indoor / urban range is up to 600m.

Here are the hardware specifications of XBee-PRO 900HP module:

  • Processors – ADF7023 transceiver and Cortex-M3 EFM32G230 @ 28 MHz
  • Frequency Band – 902 to 928 MHz, software selectable channel mask for interference immunity
  • Antenna Options – Wire, U.FL and RPSMSA
  • RF Data Rate – 10 Kbps or 200 Kbps
  • Indoor/Urban Range – Up to 2000 ft (610 m)
  • Outdoor/ Line-Of-Sight Range – Up to 9 miles (14 km) w/ dipole antenna; Up to 28 miles (45 km) w/ high-gain antenna
  • Transmit Power – Up to 24 dBm (250 mW) software selectable
  • Receiver Sensitivity – -101 dBm @ 200 Kbps, -110 dBm @ 10 Kbps
  • Data Interface-  UART (3V) and SPI
  • GPIO – Up to 15 Digital I/O, 4 10-bit ADC inputs, 2 PWM outputs
  • Networking Topologies – DigiMesh, Repeater, Point-to-Point, Point-to-Multipoint, Peer-to-Peer
  • Spread Spectrum – FHSS (Software Selectable Channels)
  • Supply Voltage – 2.1 to 3.6 VDC
  • Power – Transmit Current – 215 mA, Receive Current  – 29 mA and Sleep Current 2.5 uA
  • Regulatory Approvals:
    • FCC (USA)
    • IC (Canada)
    • C-Tick (Australia)
    • Anatel (Brazil) – Pending

The module appears to consume very little power, as transmit current is  215 mA and sleep current 2.5 uA, which means that with 15 minutes interval data, 2 AA batteries could, in theory, last a year  (Source: Twitter). Firmware can be updated over-the-air (OTA) via other XBee-PRO 900HP modules or iDigi Device Cloud service. The XBee-PRO 900HP modules does not require no programming and can be configured via AT command set or Digi’s X-CTU software.

The diagram below shows an example use in a campus to control the street lights using the RF modules and light and occupancy sensors. Data is then transmitted to a home energy gateway, which then sends data back to a remote monitoring and control office via a cellular or VPN connection.

Use Case: XBEE PRO 900HP Modules in a Campus Street Lighting System

There are 12 modules available(configuration depends on the data rate, antenna option and country) with price ranging between $39 and $42. Digi also provide the 900 MHz XBee-PRO® DigiMesh 900 development kit ($299) which include 4 XBee-PRO DigitMesh modules (1x w/ RPSMA antenna, 1x w.U.fl connector and 2 w/ a wire antenna), 4x USB development board and USB cables,  2x 900 MHz RPSMA antennas, and 2 power adapters. This kit can allow you to setup a peer-to-peer mesh network with the DigiMesh protocol (peer-to-peer networking topology).

Further information is available on Digi XBee-PRO 900HP page.